KTI Pumps + Parts (26)

DC 4000 Series Triple Acting   This Pump Features Power Up , Power Down , and Gravity Down action Used on D2 D3 D5 D7 D8 DL D9 DJ DN DS dump trailers and all powered tilts. Includes 3 button controller and translucent tank Pressure limited to 3200 psi up and 1500psi down Gravity down feature extends battery life Uses AW-32 Non Foaming Fluid or ATF Length 21.5" x Height 8" x Width 8"   Recommended Hydraulic fluid: Premium hydraulic oil with proper ISO Viscosity Grade and additives such as Chevron EP, Mobile DTE 10, DTE 20 series or Shell Tellus would be acceptable.

DC 4000 Double Acting Power Up, Power Down For applications with a double acting cylinder that extends the cylinder by power and retracts the cylinder by power. There is positive load holding on both ends of the cylinder. Motor: 12V or 24V DC Pressure: 500 – 4000 PSI (35 BAR – 275 BAR), Typical pressure for 12V DC = 3200 PSI (220 BAR) Pump: 0.5 GPM(1.875 LPM) to 5 GPM(18.75 LPM) based on specification Reservoir: Steel or Plastic, 1.5 QT (1.42 LTR) to 5 Gallon (18.93 LTR) Control: 2 button remote pendant, wireless remote   Recommended Hydraulic fluid: Premium hydraulic oil with proper ISO Viscosity Grade and additives such as Chevron EP, Mobile DTE 10, DTE 20 series or Shell Tellus would be acceptable.

 DC 4000 Series Single Acting POWER UP, GRAVITY DOWN Description For applications with a single acting cylinder that extends the cylinder by power and retracts the cylinder by gravity. Specifications Motor: 12V or 24V DC Pressure: 500 – 4000 PSI (35 BAR – 275 BAR), Typical pressure for 12V DC = 3200 PSI (220 BAR) Pump: 0.5 GPM(1.875 LPM) to 5 GPM(18.75 LPM) based on specification Control:2 button wired remote pendant 4 Qt Reservoir Technical Application Tipper/Dump Trailer Leveling System Hydraulic Jack Dump Body Lift Table Recommended Hydraulic fluid: Premium hydraulic oil with proper ISO Viscosity Grade and additives such as Chevron EP, Mobile DTE 10, DTE 20 series or Shell Tellus would be acceptable.

KTI Wireless Remote Control / Wireless Remote Control For Dump Trailer / Wireless Dump Trailer Remote Kit / KTI Hydraulic Pump Remote Kit. Wireless remote control works with any trailer built after January 2015. Very simple and quick installation. The wireless remote has a range of about 40ft with no obstructions. The receiver has a built-in safety – shuts down after being idle for 20 minutes. The receiver has the ability to program up to 4 key fobs to one receiver. Includes an inline 15 amp fuse on the power wire for protection 5/16″ eyes are included on power and ground wires to ease installation to the battery. Receiver Power and Ground Wire lengths: 24″. 2 Button receptacle connector wire length: 14″. 2 Button power unit connector wire length: 32″. The detachable antenna has a 38″ wire. Kit includes: (1) Main Transmitter(1) 23 AE Battery (for transmitter)(1) Main Receiver Unit(1) Detachable antenna(1) Antenna mounting screw(2) 2″ by 2″ velcro(1) Installation Manual *Wireless Remote Comes Preprogrammed* Wireless Instruction Manual (P/n KWR-003) Mount Wireless Receiver. Select desired mounting location preferably in a sealed box and out of harm’s way. Antenna must be mounted outside, not in metal box. Connect Pin Connector to Power Unit. (Fig. 1) Connect positive (Red Wire) & negative (Black Wire) ring terminal to Hydraulic Power Units. (Fig. 1) Connect (+) Red wire to the same terminal on Start Solenoid as positive cable from the battery. Connect (-) Black wire to motor housing or to negative terminal on the 2 terminal DC motor. Note: Insure the Power Unit is grounded directly to the negative terminal on the battery, which is the designated grounding location. Operate Wireless Unit and Remote Pendant to insure proper functionality. Up Button or OUT Down Button or IN Connect Remote Pendant to Receptacle Connector on Wireless Receiver. (Fig. 1) Functions To turn power ON or OFF, press both buttons Up and Dn simultaneously. When the receiver is in OFF mode, the LEDindicator will not illuminate. When the receiver in ON, the LED indicator will flash GREEN every 3 seconds to show that the receiver is connected to a power source above 9 Volts. If the power source is below 9 Volts the LED indicator will flash RED every 3 seconds. When receiver is ON, press any button on key fob, the LED on receiver stays ON, LED light cuts off when release button. 20 Minute Shut-down Mode (Receiver shuts down after being idle for 20 minutes). Press both buttons (Up & Dn) to turn the receiver ON. In Shutdown Mode; (Output 2) the Remote Pendant) is still active. (Fig. 1)   How to Program Remote Key Fob to Wireless Unit (Programming Mode) Remove wired hand control (Remote Pendant) to prevent accidental operation. Place Programming Sleeve (Shunt) on Pin 1 and Pin 2, to activate Programming Mode. Fig. 2,3,4 When in Programming Mode, the LED indicator will flash Red to show status. Press any button on the Key Fob, when the receiver has stored the signal from the Key Fob, the LED indicator will flash Green for2 seconds; then will flash Red to confirmation the frequency has been stored. Repeat this set when programming multiple Key Fobs. Install Program Sleeve (Shunt) on Pin 2 and 3 to end Programming Mode. (Fig. 2 & 4)Note: When in Programming Mode the transmitter must be operated within 3 – 5 seconds to program new code, otherwise the Receiver will resume previous frequency.Operating Frequency: 315MHz You may program up to 4 key fobs to one Receiver. When programming a 5th Key fob, the Receiver will drop the 1st programmed key fob. ********Wireless Receiver may not operate below 9 Volts********   How to Program Remote Key Fob to Wireless Unit (Programming Mode) Remove wired hand control (Remote Pendant) to prevent accidental operation. Place Programming Sleeve (Shunt) on Pin 1 and Pin 2, to activate Programming Mode. Fig. 2,3,4 When in Programming Mode, the LED indicator will flash Red to show status. Press any button on the Key Fob, when the receiver has stored the signal from the Key Fob, the LED indicator will flash Green for2 seconds; then will flash Red to confirmation the frequency has been stored. Repeat this set when programming multiple Key Fobs. Install Program Sleeve (Shunt) on Pin 2 and 3 to end Programming Mode. (Fig. 2 & 4)Note: When in Programming Mode the transmitter must be operated within 3 – 5 seconds to program new code, otherwise the Receiver will resume previous frequency.Operating Frequency: 315MHz You may program up to 4 key fobs to one Receiver. When programming a 5th Key fob, the Receiver will drop the 1st programmed key fob.   Get the manual here:  https://ktihydraulicsinc.com/wp-content/uploads/2018/01/KWR-003.pdf

Used in "gravity tilt" trailers to lock bed in the upright position for loading or unloading.

Remote 2 Button KTI w/15' Cord This unit will work with our hydraulic pumps on trailers built after January 2015. Very simple installation, less than 5 minutes. Kit Includes: Remote Dbl/Sgl KTI 6" 2015 Connector & Extension, KTI, 15' 2015 Connector

12V KTI 391-40

Uses a thumbwheel to hold the square coil down Vendor #LSPC-08-4 Typically used on Down circuit with square coil. Note: Does NOT fit the KTI power/up and gravity down pumps

PJ KTI replacement hydraulic 'up' valve. 2-way valve (recognized by the hex nut on top) Typically used on the 'up' circuit with a round coil. Fits KTI hydraulic power down/up pumpsNote: Does NOT fit the KTI power/up and gravity down pumps

Gravity down valve for old style KTI single acting pump. lsv2-08-2ncp

Seal Kit for KTI Pump 46-2

6 quart replacement plastic reservoir for KTI 190601 hydraulic pumps. This is for the tank only and does NOT include plugs, screws, caps or decals. This tank has a 4-11/16" round opening and a 4" square bolt hole pattern.  Length 13" X Height 7" x Width 7".

Mounting brackets are on the "bottom" opposite the posts

KTI 3 qt Reservoir Length: 6-1/2"Width: 6-1/2"Height: 6-1/2"Top bevel: 5"w x 1"hSmall holes: 1" IDLarge hole: 4-3/4" ID1-3/16" from the tank  

Used to open the hydraulic up-valve on KTI power up/down and gravity-down pumps. Slides over the valve and has two electrical prongs.

Replacement solenoid for PJ power up/down hydraulic pump. Used on dumps, tilts, and hydraulic dovetail trailers with KTI hydraulic pumps Construction: Zinc coated steel Terminal Count: 4 KTI Part number #391-19

6" cord and quick connect. This style cord has been in production since October 2015 and will be standard on KTI pumps going forward.