Wiring Harness (30)

KTI Wireless Remote Control / Wireless Remote Control For Dump Trailer / Wireless Dump Trailer Remote Kit / KTI Hydraulic Pump Remote Kit. Wireless remote control works with any trailer built after January 2015. Very simple and quick installation. The wireless remote has a range of about 40ft with no obstructions. The receiver has a built-in safety – shuts down after being idle for 20 minutes. The receiver has the ability to program up to 4 key fobs to one receiver. Includes an inline 15 amp fuse on the power wire for protection 5/16″ eyes are included on power and ground wires to ease installation to the battery. Receiver Power and Ground Wire lengths: 24″. 2 Button receptacle connector wire length: 14″. 2 Button power unit connector wire length: 32″. The detachable antenna has a 38″ wire. Kit includes: (1) Main Transmitter(1) 23 AE Battery (for transmitter)(1) Main Receiver Unit(1) Detachable antenna(1) Antenna mounting screw(2) 2″ by 2″ velcro(1) Installation Manual *Wireless Remote Comes Preprogrammed* Wireless Instruction Manual (P/n KWR-003) Mount Wireless Receiver. Select desired mounting location preferably in a sealed box and out of harm’s way. Antenna must be mounted outside, not in metal box. Connect Pin Connector to Power Unit. (Fig. 1) Connect positive (Red Wire) & negative (Black Wire) ring terminal to Hydraulic Power Units. (Fig. 1) Connect (+) Red wire to the same terminal on Start Solenoid as positive cable from the battery. Connect (-) Black wire to motor housing or to negative terminal on the 2 terminal DC motor. Note: Insure the Power Unit is grounded directly to the negative terminal on the battery, which is the designated grounding location. Operate Wireless Unit and Remote Pendant to insure proper functionality. Up Button or OUT Down Button or IN Connect Remote Pendant to Receptacle Connector on Wireless Receiver. (Fig. 1) Functions To turn power ON or OFF, press both buttons Up and Dn simultaneously. When the receiver is in OFF mode, the LEDindicator will not illuminate. When the receiver in ON, the LED indicator will flash GREEN every 3 seconds to show that the receiver is connected to a power source above 9 Volts. If the power source is below 9 Volts the LED indicator will flash RED every 3 seconds. When receiver is ON, press any button on key fob, the LED on receiver stays ON, LED light cuts off when release button. 20 Minute Shut-down Mode (Receiver shuts down after being idle for 20 minutes). Press both buttons (Up & Dn) to turn the receiver ON. In Shutdown Mode; (Output 2) the Remote Pendant) is still active. (Fig. 1)   How to Program Remote Key Fob to Wireless Unit (Programming Mode) Remove wired hand control (Remote Pendant) to prevent accidental operation. Place Programming Sleeve (Shunt) on Pin 1 and Pin 2, to activate Programming Mode. Fig. 2,3,4 When in Programming Mode, the LED indicator will flash Red to show status. Press any button on the Key Fob, when the receiver has stored the signal from the Key Fob, the LED indicator will flash Green for2 seconds; then will flash Red to confirmation the frequency has been stored. Repeat this set when programming multiple Key Fobs. Install Program Sleeve (Shunt) on Pin 2 and 3 to end Programming Mode. (Fig. 2 & 4)Note: When in Programming Mode the transmitter must be operated within 3 – 5 seconds to program new code, otherwise the Receiver will resume previous frequency.Operating Frequency: 315MHz You may program up to 4 key fobs to one Receiver. When programming a 5th Key fob, the Receiver will drop the 1st programmed key fob. ********Wireless Receiver may not operate below 9 Volts********   How to Program Remote Key Fob to Wireless Unit (Programming Mode) Remove wired hand control (Remote Pendant) to prevent accidental operation. Place Programming Sleeve (Shunt) on Pin 1 and Pin 2, to activate Programming Mode. Fig. 2,3,4 When in Programming Mode, the LED indicator will flash Red to show status. Press any button on the Key Fob, when the receiver has stored the signal from the Key Fob, the LED indicator will flash Green for2 seconds; then will flash Red to confirmation the frequency has been stored. Repeat this set when programming multiple Key Fobs. Install Program Sleeve (Shunt) on Pin 2 and 3 to end Programming Mode. (Fig. 2 & 4)Note: When in Programming Mode the transmitter must be operated within 3 – 5 seconds to program new code, otherwise the Receiver will resume previous frequency.Operating Frequency: 315MHz You may program up to 4 key fobs to one Receiver. When programming a 5th Key fob, the Receiver will drop the 1st programmed key fob.   Get the manual here:  https://ktihydraulicsinc.com/wp-content/uploads/2018/01/KWR-003.pdf

Fits Sealed Clearance Lights

Pigtail, 3 wire - Peterson LED

This harness fits domestic built carhauler trailers and connects tail tights and marker lights on back bumper.

Replaces damaged or missing USCAR vehicle harness Includes 24" color-coded, bonded wires for easy installation Like trailer hitches and ball mounts, electrical connectors range all over the board in shape, size and capability, but no matter what your trailer's electrical functions are, you need a solid connection to keep the power flowing and ensure safety on the road. CURT electrical connectors are designed and manufactured to give you a reliable connection every time you plug in your trailer. This 7-way USCAR replacement harness is designed to replace an existing USCAR plug and supply power for tail lights, turn signals, electric trailer brakes, a battery, reverse lights and brake lights, as well as a ground connection. It features rust-free black plastic construction and comes with color-coded wires and 24" of bonded wire for easy splicing into your vehicle's wiring system. This 7-way USCAR connector is a female-end socket, specifically designed for the vehicle side of the connection.

Pigtail old round Adapter, KTI 4 wire. This is the style of connector used on units built before January 2015. Harness that connects the "old round" corded remote to the pump motor and solenoids.

The vueSMART Trailer Camera is the smart way to see behind your trailer. The only wireless trailer camera that installs in minutes. Easy Do-It yourself installation uses existing trailer light No re-wiring required Adapts to work on any trailer with universal mounting bracket Hopkins Towing Solutions Mobile App is accessible to any smart device HiDef Camera delivers the widest angle behind the trailer with a full 152° degrees LED lights help with backing up at nighttime Take a picture or record video at any moment The waterproof design stands up to the harshest environments 1 Year Warranty

Remote 2 Button KTI w/15' Cord This unit will work with our hydraulic pumps on trailers built after January 2015. Very simple installation, less than 5 minutes. Kit Includes: Remote Dbl/Sgl KTI 6" 2015 Connector & Extension, KTI, 15' 2015 Connector